Water heater repair searches in Virginia more than triple between September and November, from about 2,900 a month to 12,000. Cold incoming water makes a tired heater work harder, families use more hot water, and a unit that was marginal all summer finally quits. No hot water is the call; the cause depends entirely on what kind of heater you have. Here’s how to narrow it down for gas tank, electric tank, and tankless units, and which checks are safe to make yourself.
In this article
No hot water: causes by heater type
| Symptom | Likely cause | DIY-safe? | Needs a tech? |
|---|---|---|---|
| Gas tank: no hot water, pilot out | Thermocouple, pilot assembly, or gas control valve | Relight the pilot once | Yes if it won’t stay lit |
| Gas tank: pilot lit, burner won’t fire | Gas control valve or thermostat | No | Yes |
| Electric tank: no hot water at all | Tripped high-limit reset, breaker, or failed upper element | Press the reset button once | Yes if it trips again |
| Electric tank: runs out fast | Failed lower element or broken dip tube | No | Yes |
| Any tank: rumbling, popping | Sediment on the bottom of the tank | No | Yes — flush |
| Tankless: error code, no ignition | Ignition failure, blocked intake/exhaust, flow sensor, or scale | Read the code | Yes |
| Any: water on the floor | Fitting or valve leak (repairable) vs. tank leak (replacement) | Find the source | Yes |
No hot water? Six safe checks
- Gas tank: is the pilot lit? Look through the sight window. If it’s out, follow the relight instructions on the tank once. If it lights and dies again within a minute, the thermocouple has failed — a quick repair.
- Electric tank: the reset button. Behind the upper access panel, under the insulation, is a red high-limit reset. Turn off the breaker first, press it once, restore power. If it trips again, an element or thermostat has failed; don’t keep resetting it.
- Breaker and disconnect. Electric heaters run on a 30-amp double-pole breaker that can trip on one leg. Gas heaters with power vents need their outlet live.
- Tankless: read the code. Rinnai, Navien, Noritz and Rheem tankless units display a fault code. Note it and check that the intake and exhaust outside aren’t blocked by leaves or snow.
- Temperature setting. Someone may have turned the dial down. 120°F is the standard setting; below that, it feels like no hot water.
- Find the leak. Water at the top is a fitting or the T&P valve, both repairable. Water from the bottom seam is the tank, and that’s a replacement.

No hot water: repair or replace?
Thermocouples, pilot assemblies, elements, thermostats, gas control valves, T&P valves and dip tubes are all inexpensive, single-visit repairs. Tankless descaling and flame-rod replacement are routine. Replacement makes sense when the tank itself is leaking, or when a heater past ten to twelve years has heavy sediment and rust in the hot water — at that point repairs are throwing money at a unit that’s close to the end. Our technicians tell you which case you’re in before ordering anything.
Hard water and Northern Virginia heaters
Fairfax, Loudoun and Prince William water is moderately hard, and it shortens water heater life in two ways: sediment on the bottom of a tank insulates the burner from the water, and scale inside a tankless heat exchanger throttles flow and triggers error codes. Flushing a tank once a year and descaling a tankless unit every one to two years is the maintenance that keeps a no-hot-water call from happening in December.

Appliances Pro Inc — rated 4.8★ by 513 Google reviewers, serving Northern Virginia since 2008. Open 7 days, 5 AM–10 PM. Free service call with any completed repair, 90-day parts and labor warranty.
No hot water in one part of the house only
If the kitchen has no hot water but the upstairs shower is fine, the heater is not the problem. A failed mixing cartridge in a single faucet, a crossed connection at a shower valve, or a recirculation pump that has quit will all leave one fixture cold while the tank is full. Check a second tap before you call; if every fixture has no hot water, it is the heater and the checks above apply. If it is one fixture, a plumber is the right call rather than a water heater technician.

When to call about no hot water
- The pilot won’t stay lit after one relight
- The electric reset trips again after one press
- Hot water runs out in a few minutes
- The tankless unit shows an error code
- Rumbling, popping, or rusty hot water
- Water on the floor around the heater
Call (703) 916-1130 or book online. Same-day service is usually available when you call before noon. Every completed repair includes a FREE service call, and all work carries a 90-day parts and labor warranty.
See our water heater repair page for more detail, and if you’re nearby, our appliance repair in Fairfax VA team can usually work you into the schedule quickly. For manufacturer support resources, see rheem.com support.
Frequently asked questions
Why do I suddenly have no hot water?
On a gas heater, the pilot has gone out or the thermocouple has failed. On an electric heater, the high-limit reset has tripped or an element has burned out. On a tankless unit, an ignition fault or scale has locked it out with an error code. All are repairable the same day.
Is it safe to press the reset button on my water heater?
Once, with the breaker off first. If it trips again, stop — a repeatedly tripping high-limit means a failed element or thermostat, and forcing it can overheat the tank.
Should I repair or replace my water heater?
Repair for thermocouples, elements, thermostats, valves and tankless service; replace if the tank itself is leaking or the unit is past 10–12 years with sediment and rust. We’ll tell you which before any work.
Do you repair tankless water heaters?
Yes — Rinnai, Navien, Noritz, Rheem, Bosch, Takagi and others. Descaling, flame rods, igniters, flow sensors and vent blockages are all routine tankless repairs.

